This is Thermistor 100k NTC with 1 Meter Cable Temperature Sensor for 3D Printer Reprap. The thermistor is a thermally sensitive resistor known for exhibiting a large change in resistance with only a small change in temperature.It is important to note that a thermistor’s change in resistance is non-linear. It follows a pre-defined curve which is provided by the thermistor manufacturer.Positive thermal coefficient (PTC) will increase in resistance with an increase in temperature, negative ones (NTC) will decrease. But the formula in practice is not linear, so sometimes an accurate table of measurements is better than the linear formula. These measurements can usually be found in the datasheet that accompanies the thermistor.Features :100k Ohm NTC Thermistor.NTC Thin Film Thermistor Cable.Nominal value: R25 (25 ℃) : (common) 1.5K, 2K, 5K, 10K, 20K, 30K, 47K, 50K, 100K, 200K, 500K, etc.Resistance precision: ± 1%, ± 2%, ± 3%.B value R25/50 (common) 3435k, 3600k, 3950k, 3990k, 4100k, 4200k, etc.B value accuracy: ± 1%.Recommend the use of parameters: R25℃ = 100 k B25/50 = 3950 k ± 1%)
DescriptionThis is NTC-3950 Professional Waterproof Temperature Sensor Probe. Features Stainless steel sheath and waterproofExcellent solderability and high stability in the application's environmentExcellent long-term stability Application Temperature compensation for transistors, ICs, and crystal oscillators in mobile communicationsTemperature sensor for rechargeable batteriesTemperature compensation of LCDTemperature compensation in general use of electric circuits
DescriptionThis is NTC-3950 Professional Waterproof Temperature Sensor Probe. Features Stainless steel sheath and waterproofExcellent solderability and high stability in the application's environmentExcellent long-term stability Specifications Output : 2 wires XH(2.54) -2YType : NTC 10k±1% 3950Size of probe : 5 x 25 mmLength of wire : 500 mmMeasurement range: -30 to 120 °C Application Temperature compensation for transistors, ICs, and crystal oscillators in mobile communicationsTemperature sensor for rechargeable batteriesTemperature compensation of LCDTemperature compensation in general use of electric circuits
The PT100-S Waterproof 1m 30mm Probe PTFE FTARP05 Stainless Steel Pole Probe Temperature Sensor has a water-immersible probe suitable for precision air or liquid temperature measurements.You can immerse both the probe and the cable in the water for continuous operation. It also can be used with a thermal well.
DS18B20 Temperature Sensor Module is a digital temperature sensor, and you can easily connect it to Arduino with only one 4.7-pound resistor, base 1 – Ground 2 – Output – Base 3 to the positive of the source, with resistance to base 2 Is connected. The connection of this sensor to the Arduino via the 1-wire protocol is established. Therefore, several sensors can be connected only through one common wire to Arduino. The output is digitally accurate to 12 bits. Therefore, the temperature can be measured with a precision of 0.0625 º C.Applications:DS18B20 Temperature Sensor is suitable for the cold storage, granaries, storage tanks, telecommunications room, electric power room, cable trough, and other temperature measurement and control areas; bearing, cylinder, textile machinery, air conditioning, and other small space industrial equipment temperature and control; , Refrigerator, freezer, and low-temperature drying oven, etc. heating/cooling pipe calorie measurement, central air conditioning household thermal energy measurement and industrial temperature measurement and control and Many more..Features: Digital signal output18B20 Temperature Sensor ChipResolution adjustment ranges from 9-12 bytes.Send data via a pinTemperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.
A probe by new original installation import DS18B20 temperature sensor chip.Stainless steel tube encapsulation waterproof moistureproof prevents rust.Stainless steel shell (6 * 45 mm), lead length 100 mm (shielding wire) use stability;3.0 V-5.5 V power supply;Temperature range wide: -55 ℃ ~ + 125 ℃;Without the external components, the unique single bus.
This DS18B20 temperature sensor (TO-92) is very useful for temperature control in consumer products, industrial systems, and in many thermal measurement systems. This DS18B20 temperature sensor (TO-92) is designed to measure the temperature of the environment.Specifications IC Output Type: digitalSensing Accuracy: ± 0.5 ° CRange of Temperature Detection: - 55 ° C to + 125 ° CCurrent: 1 mAVoltage Range: 3 V to 5.5 VNumber of Pins: 3Operating Temperature Min: - 55 ° COperating Temperature Max: 125 ° COperating Temperature Range: - 55 ° C to + 125 ° C